Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Installation in Garland: What to Know First
FAAC gate installation in Garland runs between $1,850 and $6,400 for most residential jobs, depending on the operator model, gate weight, and whether we’re working with an existing frame or starting fresh. We install FAAC swing and slide operators as an independent provider, and we typically schedule installation work within five to seven business days of the site visit. Every quote is written, itemized, and handed to you before any work begins.
This page is for Garland homeowners who already own a FAAC operator or have decided on one and need a crew that actually knows the equipment. If you’ve got an E024U sitting in a box in the garage, or your old 770 series finally gave out and you’re weighing repair against replacement, we can help you sort it. Call (469) 273-6254 and we’ll send a technician who works on FAAC equipment every week.
How FAAC Products Fail and How We Fix Them
FAAC builds solid operators, but we see the same failure patterns across Garland driveways. Here’s what actually goes wrong and what we do about it:
- E024U capacitor failure on hot afternoons. The E024U is one of the most common FAAC swing operators in Garland residential work. Its start capacitor sits inside a compact housing with limited airflow. After three or four Texas summers, the capacitor degrades and the gate starts moving slower, then stops mid-travel. We replace the capacitor with an OEM-spec unit and confirm the limit settings afterward, because a gate that’s been limping along often has drifted limits too.
- S800H hydraulic pump pressure loss on older installs. The S800H is a workhorse, but on units that are ten years old or more, we frequently find the hydraulic pump has lost pressure due to internal seal wear. The symptom is a gate that opens fine cold but struggles once the fluid warms up. Repairing the pump is usually viable if the gate weight is within spec, and we’ll tell you honestly if it isn’t.
- Limit switch drift on 400 and 750 series operators. These mechanical limit switches are adjustable, which also means they can drift. A gate that closes an inch too far or stops short is usually a limit issue, not a motor issue. We reset the limits, run the gate through ten full cycles, and photograph the final position so you have a record of where it was set.
- Control board damage from Garland storms. Power surges during spring storm season are a real factor here. FAAC control boards are sensitive, and we’ve replaced enough of them after lightning-adjacent strikes to recommend a surge protector on any new FAAC install. It’s a $75 to $150 add-on that saves a $400 to $700 board.
- Photo-eye misalignment on slide gate installs. FAAC slide operators rely on photo-eyes, the infrared safety beams that stop the gate when something crosses the path. On Garland properties with shifting clay soil, the posts holding those eyes can move over time. A gate that reverses for no reason is almost always a beam alignment issue. We realign, shim the post if needed, and test the obstruction response before we leave.
Our FAAC Gate Installation Process
Every FAAC job follows the same sequence. No shortcuts, no surprises.
- 1
Site visit and measurement. We measure the gate leaf, weigh it if it’s already hung, check the post condition, and confirm the electrical run. This is free and takes about an hour.
- 2
Written scope and price. Before any work starts, you get an itemized quote: operator model, mounting hardware, control board, safety edges, photo-eyes, and labor. The price we write is the price you pay.
- 3
Parts decision. If you already own the FAAC operator, we install it and flag anything missing from the box. If we’re sourcing, we use OEM FAAC parts unless you ask us to price an aftermarket alternative. We’ll explain the trade-off in dollars and warranty terms, not just hand you a cheaper part.
- 4
Installation day. We mount the operator, run the wiring, install or verify safety devices, and connect the control board. Every connection is tested before we adjust anything else.
- 5
Full cycle testing. The gate runs through at least ten full open-close cycles, including obstruction tests on the safety edges and photo-eyes. We check the force settings against FAAC’s specs for your gate weight.
- 6
Documentation and walkthrough. You get a photo log of the install, the written record of settings, and a walkthrough of how to operate the gate manually during a power outage. The 365-Day Done Right Promise applies to the entire job.
BeforeAfterWhat FAAC Gate Installation Costs in Garland
Here’s what we quote on FAAC jobs in Garland. These are real ranges from actual quotes, not national averages pulled from a database.
| Scenario | Price Range |
|---|---|
| Install customer-supplied FAAC swing operator (E024U, 400 series) on existing gate | $850 to $1,450 |
| Full FAAC swing operator install, including operator | $2,100 to $3,400 |
| FAAC slide operator install on existing track gate | $2,400 to $3,800 |
| Double swing gate with two FAAC operators and full safety package | $4,200 to $6,400 |
| Surge protection, photo-eye replacement, or safety edge addition during install | $75 to $350 per item |
What moves the price: gate weight and condition, the quality of the posts, the distance to the nearest power source, and whether we’re adding safety edges or surge protection. The quote you get is the quote you approve, and it doesn’t change unless the scope changes and you agree to it in writing. Call (469) 273-6254 for a free estimate.
Why Garland Homeowners Call Vance Gate Repair Garland for FAAC Work
There are gate companies in Garland that’ll put in whatever motor you ask for. There are fewer that can actually troubleshoot a FAAC when something’s off. We service nine automation brands, and that matters because we’re not going to steer you toward replacing a FAAC that still has good years left just because it’s the brand we sell. LiftMaster, Mighty Mule, Ghost Controls, DoorKing, and FAAC are all brands we work on, which means our recommendation about your FAAC is based on what’s actually wrong with it, not what we’d rather sell you.
Adrian Vance started this work on commercial access-control sites, and he brought the documentation habit with him. The same approach applies on a residential driveway in Garland: name what you found, name what it costs, name what you left behind. That’s the whole job.
Every FAAC install carries the 365-Day Done Right Promise. If it isn’t right, we make it right, at no charge, within the year. And a live person answers our phone 24 hours a day. No voicemail tree, no callback queue. Call (469) 273-6254 and you’ll talk to someone who can help.
FAQs
FAAC’s warranty covers manufacturer defects, not installation errors. If you install it yourself and something fails because of incorrect wiring or a misaligned limit, that repair is on you. We install FAAC operators according to the manufacturer’s specifications, which keeps legitimate warranty claims valid and protects the equipment. If you’ve already started a DIY install and hit a wall, we can pick up where you left off. Call (469) 273-6254 and we’ll give you an honest assessment.
A standard single swing gate FAAC install takes one full day. A slide gate or double swing gate takes one to two days, depending on the concrete work and electrical run involved. We schedule most FAAC installations in Garland within five to seven business days of the free site visit. Weather delays happen in spring, but we keep you informed.
If the operator is under 8 years old and the failure is a known component, like a capacitor, limit switch, or photo-eye, repair usually makes sense. If it’s a hydraulic pump on a 12-year-old S800H and you’re looking at a $1,100 rebuild on a gate that’s also sagging, replacement might be the smarter money. We’ll show you both numbers in writing and let you decide. We don’t push replacement when repair is the honest call.
Yes, we install customer-supplied FAAC operators. We’ll inspect the unit before we start, confirm it’s the right model for your gate weight and hinge setup, and flag any missing components before they become an installation-day problem. We can’t warranty the operator itself if you bought it, but our labor and the 365-Day Done Right Promise still apply. Call (469) 273-6254 to schedule a site visit.
Yes, as long as the gate is structurally sound and the posts can handle the load. In Garland, we regularly see wrought iron gates near the Firewheel Town Center corridor that have been hanging for 15 years and just need new hinges, a fresh operator, and proper limit calibration. If the gate itself is twisted or the post is rusted through, we’ll tell you that before we quote the FAAC install, because a new operator on a failing frame is money wasted.
Written by Adrian Vance, Owner, Vance Gate Repair Garland at Vance Gate Repair Garland, serving Garland and nearby areas.