Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Motor & Opener in Garland: What to Know First
FAAC gate motor and opener repair in Garland typically runs $245-$680 for most service calls, with complete swing-arm operator replacements landing between $1,400 and $2,900 depending on the model and what’s salvageable. We’re an independent FAAC service provider in Garland, not a factory shop, which means we diagnose the motor you already own before anyone suggests replacing it. Most FAAC jobs are same-day or next-day once we confirm the symptoms on the phone.
If your FAAC gate stopped mid-travel, won’t respond to the remote, or is grinding when it runs, call (469) 273-6254. A live person answers, and the first question we’ll ask is what the motor is doing, not what your budget is.
How FAAC Products Fail - and How We Fix Them
FAAC builds a solid operator. But every brand has its patterns, and after years of service calls across Garland, we know exactly where FAAC units tend to give out before we open the cover.
- FAAC 400 Series (swing gate) – capacitor failure after 5-7 years. The 400 and 402 operators use a start capacitor that degrades in North Texas heat. The symptom is specific: the gate hums but won’t move, or moves an inch and stops. We test capacitance on-site, and if it’s below spec, we replace it with a matched OEM capacitor. Total fix is usually under $300 including the part.
- FAAC 750 and 760 slide operators – limit switch drift. The mechanical limit switches on the 750 line work loose over time, especially on gates that cycle more than 20 times a day. The gate over-travels and slams the end stop. We re-set the limits, torque the fasteners, and photograph the final position so you have a record of where they should stay.
- FAAC 391 and 770 – hydraulic fluid degradation. These hydraulic operators are sensitive to temperature swings we get in Garland, where a February cold snap follows a 75-degree January. Old fluid thickens, the gate moves slow, and the pump strains. We flush and refill with the correct FAAC-spec hydraulic oil, not whatever’s on the shelf at the parts store.
- FAAC 844 control boards – relay chatter from power surges. The 844 board is a workhorse, but Garland’s spring storm season isn’t kind to it. After a lightning strike nearby, the relays click rapidly and the gate won’t hold position. We check the board’s fuse and relay contacts first; if the board is fried, we quote an OEM replacement and show you the test readings before we order anything.
- FAAC S700 and S800 high-speed operators – photocell misalignment. These are built for commercial and high-traffic residential use, and their safety photo-eyes get knocked out of alignment by wind, lawn equipment, or a delivery truck bumper. The gate opens but refuses to close. The fix is realignment and a sensitivity check, usually a 30-minute call. We’ve seen this exact issue on driveways near Firewheel Town Center where wind off the open lots shifts the photocell mounts.
Our FAAC Gate Motor & Opener Process
Every FAAC job in Garland follows the same sequence. The Haven Standard isn’t a slogan, it’s how we hand you the paperwork.
- 1
The call. You describe what the gate is doing. We ask about the model number, which is on a silver sticker inside the operator cover. If you can’t reach it, we work from the symptoms. We tell you the service-call fee and what it covers before we schedule anything.
- 2
On-site diagnosis. The tech arrives with the parts our FAAC calls most often need: capacitors, limit switches, photocells, fuses, and hydraulic fluid. We test the motor, the board, and the safety edge before we quote a single dollar of repair work.
- 3
The written price. We hand you a written scope and a flat price, not an estimate with a range. If the repair needs an OEM part we don’t have on the truck, we tell you the lead time and the total. You approve it or you don’t. Nothing gets opened that you haven’t agreed to pay for.
- 4
The repair. We install OEM FAAC parts where the warranty matters, and we’ll recommend quality aftermarket only when it’s an honest equivalent, like generic hydraulic fluid or a universal photocell. We never use aftermarket capacitors or control boards: that’s where the failure chain starts.
- 5
Testing and documentation. We cycle the gate at least ten times in both directions, test the obstruction-reversal, and verify the auto-close timing if your FAAC has it. Every cycle is logged.
- 6
What you’re left with. You get a photo log of what we found, what we set, and what we installed. Part numbers, limit-switch readings, and torque values go in the record. Clause 4 of The Haven Standard is Evidence on every job. We don’t leave until you’ve seen the pictures and understand what changed.
BeforeAfterWhat FAAC Gate Motor & Opener Costs in Garland
Here’s what we actually charge for FAAC work in Garland. These are flat prices, not ranges we expand after the fact.
- Service call and diagnosis: $85-$125, applied to the repair if you proceed
- Capacitor replacement (400/402 series): $245-$310
- Limit switch reset and adjustment (750/760): $180-$260
- Photocell realignment or replacement: $190-$340
- Control board replacement (844 series): $520-$890
- Complete swing-arm operator installation (FAAC 400 or 402): $1,600-$2,400
- Complete slide operator installation (FAAC 750/760): $1,900-$2,900
The price moves based on what’s reusable: if your arm bracket and mounting post are intact, you’re not paying for new ones. If the hydraulic lines need replacing, that’s line-itemed separately. We write it down, you read it, and the price doesn’t change unless you add scope. Call (469) 273-6254 for a written quote on your specific FAAC model. The quote is free, and it’s the same document you’ll sign before any work begins.
Why Garland Homeowners Call Vance Gate Repair Garland for FAAC Work
We repair FAAC operators because we know them, not because FAAC sent us a certificate. We’re independent. That’s the point: we work for you, not for a manufacturer’s parts quota.
Every FAAC job we finish is covered by the 365-Day Done Right Promise. If the repair isn’t right, we make it right within a year, no argument and no second invoice. We also document everything: the wiring diagram, the limit-switch settings, and the photo log are yours to keep. That’s not a courtesy, it’s Clause 4.
One more thing. We service nine automation brands, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. If your property has a FAAC on the driveway and a Ghost Controls on the pedestrian gate, we handle both on the same visit. No one has to call two companies. Adrian Vance started this business in 2014 with a notebook and a voltmeter, and the notebook is still in the truck. Name what you found. Name what it costs. Name what you left behind. That’s the whole job.
FAQs
If your FAAC operator is still under the manufacturer’s warranty, we can handle the repair as an independent FAAC service provider and give you the documentation the warranty claim requires. We don’t process claims for you, but we hand you a complete record: the failed part, the test readings, and photos. Under our own 365-Day Done Right Promise, any repair we make is covered for a full year regardless of the manufacturer’s warranty status. Call (469) 273-6254 and we’ll tell you what your model’s warranty actually covers.
We stock the FAAC parts that fail most often in North Texas: start capacitors for the 400 series, limit switches for the 750 line, photocells, and control-board fuses. Most common repairs happen same-day from the truck. If your operator needs a less common part, like a specific control board or hydraulic pump, the lead time is usually 3-7 business days, and we’ll give you the date in writing before you commit. We don’t charge for parts we haven’t ordered yet.
We repair before we recommend replacement, and that’s not a slogan. Most FAAC motors we see in Garland are between 5 and 15 years old, and the majority of failures are repairable parts: capacitors, limits, photocells, and fluid. If the cost of repair exceeds 50-60% of a new operator, or the motor has seized, we’ll tell you that and show you the numbers. Replacement only gets recommended when the math says it should be. You approve either decision in writing first.
We keep same-day repair slots open for exactly this situation. Most FAAC failures in Garland are diagnosed and repaired on the same call, including capacitor swaps and limit-switch resets. If the motor is completely dead and the board is at fault, we may need a follow-up visit once the part arrives. Call (469) 273-6254 and describe what the gate is doing. If it’s a safety issue, like a gate stuck open on a busy street, tell the dispatch team and we’ll prioritize your address.
Yes, this is one of the most common upgrades we do on FAAC swing and slide operators in Garland. A properly sized battery backup keeps your gate cycling through the power outages that come with spring storms and summer brownouts. We install the correct FAAC-rated battery and charging module, test the transfer under load, and document the runtime you can expect. It’s a half-day job on most models, priced in writing before we start.
Written by Adrian Vance, Owner, Vance Gate Repair Garland at Vance Gate Repair Garland, serving Garland and nearby areas.