Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Motor Replacement: The Garland Owner’s Guide
FAAC gate motor replacement in Garland typically runs $850 to $1,650 installed, depending on the model series and whether the arm bracket and mounting plate are still intact. We stock FAAC-compatible replacement motors and can usually complete a swap the same day we diagnose the failure. Most Garland homeowners discover the problem on a Monday morning: the gate groans, stops mid-travel, or refuses to move at all, and the LED on the control board blinks a fault code nobody has time to decode before work.
What you’re looking at is a failed operator, not necessarily a failed gate. The motor itself may be done, but the failure usually has a story: a capacitor that quit on a cold snap, a gear that stripped after years of wind load against a solid panel, or a control board that took a power surge during a spring thunderstorm. We name the part, name the price, and leave you with the documentation to prove what was found. That’s how we work in Garland, and it’s how Adrian Vance has run the shop since 2014.
Which FAAC Models This Applies To
We replace FAAC motors across the residential swing-gate lines most common in Garland: the 400 Series (including the 402, 412, and 415 operators), the 770 Series for heavier gates, and the C720/C721 for underground applications. We also service the newer E-Series swing operators, though those are less common in North Texas residential work. If you’re not sure what you have, the model number is printed on a silver label on the operator body, usually near the release handle or on the underside of the cover. Take a photo of it before you call. It saves a trip.
The compatibility gotcha with FAAC is this: the 400 Series and 770 Series use different mounting footprints and different arm geometries. A 402 motor will not drop into a 770 bracket without modification, and an aftermarket arm from the wrong series will bind at the elbow on the first cycle. We match the motor to the series, not just to “a FAAC swing gate.” On the OEM-versus-aftermarket question, our position is plain: FAAC OEM motors are built for a 20,000-plus cycle life in testing, but a quality aftermarket equivalent from a reputable supplier often runs 15 to 20 percent less and carries a comparable warranty. We install both, we tell you the difference in writing, and we don’t mark up parts to make one look better than the other.
Signs Your FAAC Gate Motor Replacement Is Failing
- The gate hums but doesn’t move. The capacitor is usually failing or the motor’s start winding is compromised. If the capacitor is swollen or leaking, the motor will often still run once started but won’t start under load.
- Intermittent operation, especially after rain or humidity shifts. In Garland’s clay-heavy soil and spring thunderstorm season, moisture ingress through a worn seal or cracked terminal cover corrodes connections and makes the operator behave unpredictably.
- The gate moves slowly or loses power halfway through the cycle. Worn brushes or a binding gearbox can drag the motor’s RPM down. By the time it’s this obvious, the motor has been compensating for months.
- The gate reverses mid-cycle or stops and re-opens. Often mistaken for a photo-eye problem, but a failing motor can trip the obstacle-detection circuit by drawing excess current under load.
- Burnt smell or visible scorching near the motor housing. This is the motor windings overheating. Stop running the gate and cut power at the breaker. A scorched motor is a fire hazard, not a repair-and-wait part.
BeforeAfterReplacement Cost & What’s Included
In Garland, you can expect these installed price ranges for FAAC gate motor replacement:
- FAAC 400 Series (402/412/415) motor replacement: $850 to $1,150 installed
- FAAC 770 Series motor replacement: $1,200 to $1,650 installed
- FAAC C720/C721 underground motor replacement: $1,600 to $2,400 installed (includes excavation and re-bedding the foundation box)
What drives the range is the condition of the mounting hardware, whether the arm bracket survived the failure, and whether the control board needs reprogramming or replacement alongside the motor. We quote the motor, the labor, and any hardware as separate line items in writing before work starts. You know the number. The price we hand you is the price you pay unless you approve a change in writing first. Every FAAC motor replacement includes our 365-Day Done Right Promise: if it’s not right within a year, we make it right at no charge.
DIY or Call Us?
What a Garland owner can safely check: whether the breaker is tripped, whether the release handle is fully engaged, whether leaves or mud are blocking the arm’s travel, and whether the control board shows a fault code you can photograph and send to us. That’s five minutes of work and it often rules out the simple stuff. What you should not do is open the operator housing and start probing the capacitor or wiring. A FAAC motor’s capacitor holds a charge even with the power off, and the swing arm is under spring tension. The wrong move can send that arm through a fence panel or into a hand.
If the motor is humming, dead, or scorched, call (469) 273-6254. A live person answers. We’ll schedule a diagnostic, write the quote in front of you, and if you approve it, we’re usually installing the same day.
FAQs
In Garland’s heat and summer storm cycles, a FAAC residential swing motor typically lasts 8 to 12 years before the capacitors, brushes, or gearbox internals start to fail. Gates that run 40-plus cycles a day will wear faster than ones that see six.
Sometimes. A failing capacitor, worn brushes, or a seized release mechanism can be serviced without replacing the whole motor. We’ll tell you if repair is viable and what the repair would cost against replacement. If the windings are scorched or the gearbox is grinding, replacement is the honest answer. Call (469) 273-6254 and we’ll give you the diagnosis in person, in writing.
Most 400 Series and 770 Series replacements take 90 minutes to three hours on site, including mounting, wiring, limit setting, and a full travel test. Underground C720/C721 jobs are usually a half-day or longer because they involve digging out the foundation box.
We stock the most common 400 Series motors and arms on our service vehicles, and we keep 770 Series motors at our Garland yard for same-day install in most cases. Underground and specialty models may take 2 to 5 business days to source. We’ll tell you at the diagnostic what’s on hand and what’s not, and you decide before anything is ordered.
Contact Vance Gate Repair Garland
If your FAAC gate motor is failing in Garland, call (469) 273-6254. We’ll send a background-checked, uniformed technician, name the problem, hand you a written price, and leave you with a documented photo record of everything we touched. We also stock parts for LiftMaster, Mighty Mule, and Ghost Controls operators, and we’re an independent service provider, not affiliated with FAAC. Same-day motor replacement is available in most Garland neighborhoods, including the Firewheel Town Center corridor. Free estimates, upfront pricing, and the 365-Day Done Right Promise on every install.
Written by Adrian Vance, Owner, Vance Gate Repair Garland at Vance Gate Repair Garland, serving Garland and nearby areas.