Gate Repair in Plano - Fixed Today, No Surprise Invoice

Gate Repair in Plano, TX

Gate access control in Plano usually means a keypad, card reader, or phone entry system that has stopped talking to an aging operator, a failed maglock, or a circuit board that finally gave up after one too many triple-digit summers. Most of the calls we run in Plano come from subdivisions built between 1985 and 2005, where the original entry hardware is now 20 to 30 years old and the HOA expects any replacement part to match the existing finish. If your gate won’t open from the keypad or the phone entry won’t ring through, call (469) 273-6254 and we’ll send a technician who can diagnose it on site.

Call (469) 273-6254

Why Plano Homes Are Different

Plano’s master-planned subdivisions were built in waves, and a lot of them put automated gates in at the front end. Those original operators, underground vehicle loops, and keypads are aging out together now, which means a call that starts as “the gate is slow” often ends with a loop detector, an operator, and a concrete post needing work in the same visit. The west-side communities near Legacy and Willow Bend carry a lot of wrought-iron perimeter fencing, so hinge and post repairs there have to blend with existing ornamental iron rather than swap in a generic component.

The soil under Plano is North Texas black clay, and it moves. Dry summers shrink it; wet springs heave it. Posts drift out of plumb, swing gates go out of square, and slide-gate tracks misalign by fractions of an inch that matter. Sustained July and August heat also pushes exposed circuit boards and battery backups past their rated tolerances, so we see a predictable spike in control-board failures every summer. And because so much of Plano is HOA-governed, repairs often require spec approval from the management company before a single part gets ordered. That step doesn’t exist at this scale in most surrounding cities.

Our Main Plano Services

Plano homeowners call us most often about gate repairs, full installations, and motor or opener problems. Here’s what each involves here.

Gate Repair in Plano

Most repair calls in Plano fall into two buckets: a gate that won’t open or close, and a gate that no longer sits square in its opening. Black-clay soil movement is behind a lot of the second bucket. Our technicians reset posts, realign tracks, replace hinges, and rehang gates so they clear the latch and close without dragging. The flat price is written before any work starts, and every adjustment gets photographed for your record. Gate Repair in Plano covers the common repairs and what they run.

Gate Installation in Plano

New gate work in Plano usually means matching an existing ornamental iron or powder-coated aluminum profile, which requires sourcing the right material rather than grabbing whatever is in stock. HOA approval often comes before we order anything. We measure, write the scope, and give you a fixed price before any fabrication begins, then install with the operator, safety edges, and a documented photo log at the end. Gate Installation in Plano walks through the full process for this city.

Gate Motor & Opener in Plano

Operator failures spike in Plano every summer when heat pushes boards and battery units past their limits. We service nine automation brands including Linear, Viking, and DoorKing, so we can usually repair the motor already on the property instead of pushing a replacement. Limit switches, photo-eyes, arm brackets, and control boards are diagnosed on site. Gate Motor & Opener in Plano has the full breakdown.

Before

After

Gate Access Control in Plano

Access control in Plano means the keypads, card readers, phone entry systems, and video intercoms that decide who gets through a community or driveway gate. In a city with this many HOA-governed subdivisions, the entry hardware often has to match what the board approved decades ago, which changes how we spec parts and who has to sign off before we order. Gate Access Control covers our full service line, and here’s what we see most in Plano.

Keypad Entry

Signs you need it

You punch in the code and nothing happens, or only some digits register, or the keypad works intermittently after rain.

What it costs in Plano

Keypad replacement runs $180 to $450 here, depending on whether it’s a surface-mount unit or a pedestal-mounted model that needs new conduit.

How we do it

We test voltage at the keypad, open the housing to check for corrosion, replace the unit or the wiring run, then reprogram and photograph the finished install.

Phone Entry

Signs you need it

Calls don’t ring through to your phone, the gate won’t open from the app, or the unit shows an offline status at the panel.

What it costs in Plano

Phone entry repairs typically run $150 to $550 in Plano, depending on whether we’re replacing a relay, a cellular module, or the whole controller.

How we do it

We verify the phone line or cellular signal, test the relay, and replace the failed module or controller, then log the new settings in your job record.

Card Reader

Signs you need it

Cards work for some residents but not others, or the reader beeps but never sends a signal to the operator.

What it costs in Plano

Readers and control boards run $250 to $600 in Plano when the hardware is aged out, and more if the underground wiring has failed.

How we do it

We test the reader output at the board, isolate whether it’s the reader, the wiring, or the controller, then replace only what failed.

What Gate Access Control Costs in Plano

Does HOA approval slow down access control work in Plano?

Yes, often. Many Plano subdivisions require the HOA to approve any entry hardware change before we order parts. We handle that coordination, but it can add days to the timeline. Call (469) 273-6254 and we’ll tell you what your community requires.

Can you integrate a new keypad with my existing gate operator?

Usually, yes. We service Linear, Viking, Ghost Controls, DoorKing, and other major operators, so a new keypad can typically wire into the motor already on your property. We confirm compatibility before quoting anything.

Gate Parts & Welding in Plano

Gate parts and welding in Plano are shaped by two realities: the ornamental iron and powder-coated aluminum profiles that dominate HOA-governed subdivisions, and the black-clay soil that keeps moving posts and breaking welds. When a hinge tears or a post tilts, the repair has to match the existing fence line and hold through the next soil cycle. Gate Parts & Welding is our dedicated service hub, and here’s what we do most in this city.

Hinge Replacement

Signs you need it

The gate sags, scrapes the ground on the latch side, or the hinge pin is visibly bent and the gap at the top of the gate isn’t even.

What it costs in Plano

Hinge replacement runs $120 to $400 per hinge in Plano, depending on the weight of the gate and whether we need to weld new plates to the post.

How we do it

We lift the gate, cut out the failed hinge, weld or bolt in a matching replacement, and set the gate back level.

Post Replacement

Signs you need it

The post leans, the gate catches on the latch, or you can see cracking at the base where the post meets the concrete footing.

What it costs in Plano

Steel post replacement runs $200 to $850 per post in Plano, with wood or ornamental work falling in the $150 to $700 range depending on access and depth.

How we do it

We dig out the failed post, set a new one in concrete at the correct depth for Plano’s soil, and make sure it’s plumb before the concrete cures.

Custom Welding

Signs you need it

A picket has broken free, a section of the frame is cracked, or a previous repair has rusted through and failed again.

What it costs in Plano

Custom welding jobs in Plano typically fall between $120 and $450 per hour depending on the material thickness and whether it’s ornamental iron or aluminum.

How we do it

We grind back the break, weld the joint, and grind the bead smooth so it matches the surrounding profile and takes paint evenly.

What Gate Parts & Welding Costs in Plano

Can you match the finish on an ornamental iron gate in Plano?

Yes. We source matching profiles and powder-coat finishes so the repair blends with the existing fence line. For HOA-governed properties, we’ll send photos of the proposed material before any work starts.

Do you weld gates that aren’t ornamental iron?

We weld steel, aluminum, and most gate metals common in Plano. Aluminum needs a different process than ornamental iron, so we inspect the material before quoting. Call (469) 273-6254 and we’ll take a look.

Brands We Service in Plano

We work on Linear, Viking, Ghost Controls, and DoorKing operators, plus five other major automation brands, and we stock common parts for faster turnaround in Plano. Our technicians are trained across all nine brands, so we repair what’s on the property rather than steering you toward a replacement. See our brands for the full list.

Pricing for Gate Repair in Plano, TX

Neighborhoods We Serve in Plano

We run gate repair calls across Plano, from the gated communities near Legacy and Willow Bend to the established subdivisions east of 75. Our typical response window in Plano is same-day or next-morning for repair calls, with scheduled visits for installation and welding work.

• Legacy
• Willow Bend
• Whiffletree
• Gleneagles
• Kings Ridge

Service Area - Cities Near Plano

If you’re just outside Plano, we also run gate repair and installation work in Allen, TX, Richardson, TX, Carrollton, TX, and Garland, TX. The same written pricing and photo-documented record apply everywhere we go.

FAQs About Gate Repair in Plano