Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterWeld & Rust Repair in Garland, TX
Weld and rust repair for residential gates in Garland typically costs between $150 and $450, depending on the extent of the corrosion and whether the structural integrity of the gate frame has been compromised. If you notice sagging gate panels, hinges pulling away from steel posts, or visible orange oxidation flaking off your gate’s framework, you likely need a professional evaluation to prevent total gate failure. At Vance Gate Repair Garland, our Gate Repair services handle these issues by stripping the rusted areas, reinforcing the metal with new steel, and sealing the joints to prevent further water intrusion. You can reach us at (469) 273-6254 to schedule an onsite assessment; we provide a written price before any work begins, following our Haven Standard Clause 1.
Rust is a constant battle in North Texas, where fluctuating humidity levels and intense heat accelerate the oxidation process on iron and steel gates. When a weld fails, it usually happens at the stress points-the hinges, the latch receiver, or the bottom rail where water pools after a heavy storm. We don’t just patch over the problem. Our approach involves grinding down to clean metal, welding new bracing where necessary, and ensuring the structural load is properly distributed. This service is a specialized branch of our broader Gate Repair work, ensuring your entry remains secure rather than becoming a safety hazard.
When You Need Weld & Rust Repair
Not every spot of rust requires a welder, but certain signs indicate that your gate’s structural health is at risk. If you see these indicators, it is time to have a professional look at the metalwork before a minor repair turns into a full gate replacement.
- Hinge Separation: If you see cracks or gaps forming where the hinge plate attaches to the post or the gate frame, the welds have likely failed from metal fatigue. This is common on heavy ornamental iron gates in Garland neighborhoods with older, established driveways where ground shifting puts extra torque on the gate.
- Bottom Rail Decay: The bottom rail of a swinging gate often collects debris and moisture. If the metal feels soft or flaky when touched, or if there are holes rusted through the steel, the gate is losing its structural rigidity and needs reinforcement.
- Sagging or Dragging: When a gate drags on the pavement, it is often because the frame has twisted due to failed welds at the corners. This puts immense strain on your gate motor, such as a Linear or Viking unit, which was never designed to lift the weight of a dragging gate.
- Latch Misalignment: If your gate latch no longer catches properly because the gate has shifted downward, the root cause is often a broken weld at the hinge side. We verify the frame alignment before adjusting the latch to ensure the fix lasts.
- Visible Corrosion at Joints: Surface rust is cosmetic, but deep, pitting rust at the joints where two pieces of metal meet indicates that moisture has compromised the weld bead. This requires grinding and re-welding to restore the strength of the connection.
Our Weld & Rust Repair Process
Under the Haven Standard, we believe in transparency and evidence. You aren’t just paying for a weld; you are paying for a documented repair that we stand behind. Here is how we handle weld and rust issues at your property.
- Assessment and Documentation: We arrive at your Garland home, inspect the gate, and identify the specific failure points. Per Clause 4 (Evidence on every job), we take photos of the rusted areas and the failed welds to show you exactly what is happening before we discuss a price.
- Surface Preparation: We strip away the rusted metal, paint, and scale using industrial grinders. Welding onto rust creates a weak, porous bond that will fail again in months. We get down to bare, shiny steel to ensure the new weld holds.
- Structural Reinforcement: If the original metal is too thin to hold a weld, we fabricate and weld in a steel patch or gusset. This adds strength back to the joint, often making it stronger than it was when the gate was new.
- Finishing and Sealing: Once the weld is complete and cooled, we grind it smooth to match the existing profile of the gate. We then apply a rust-inhibiting primer and, if you have the touch-up paint on hand, we can apply that as well to keep the repair discreet.
- Final Verification: We test the gate’s movement and alignment, ensuring the hinges operate smoothly and the latch engages without resistance. We provide you with a final photo log of the repair, documenting the work performed for your records.
BeforeAfterWeld & Rust Repair Pricing in Garland
We provide upfront, written pricing so you know exactly what the cost is before we plug in our equipment. Because every gate is unique-ranging from simple steel tube frames to heavy, intricate ornamental iron-we price based on the complexity of the repair and the amount of metal fabrication required.
| Service Type | Typical Cost Range |
|---|---|
| Small weld repair (single hinge or latch point) | $150 – $250 |
| Structural reinforcement (patching rusted rails) | $250 – $450 |
| Major frame repair (corner re-welding/re-alignment) | $400 – $700+ |
These prices include the labor, consumables like welding rods and shielding gas, and the documentation we provide. If you have a written estimate from another company, bring it to us. We offer a free second opinion on any written estimate to ensure you are getting an accurate scope of work. Call (469) 273-6254 to discuss your gate’s condition; we provide free estimates on all repairs.
FAQs - Weld & Rust Repair
Can you fix my gate if it’s dragging on the driveway?
Yes, we frequently repair dragging gates, but the fix depends on why it is dragging. If the issue is a broken weld at the hinge or a twisted frame, we can weld the structure back into alignment and reinforce the weak points. We do not recommend trying to lift the gate yourself, as the weight can shift unexpectedly and cause injury; call us at (469) 273-6254 for Gate Realignment and an onsite evaluation.
Do you paint the gate after welding?
We apply a high-quality, rust-inhibiting primer to the repaired area to prevent immediate re-oxidation, but we do not perform full-gate painting or powder coating. We recommend having a color-matched spray can on hand so you can blend the primed area with the rest of your gate once the repair is complete.
Why does my Ghost Controls gate keep stopping?
If your Ghost Controls or DoorKing motor is stopping mid-cycle, it is often detecting resistance caused by a misaligned gate or a failing hinge, which may require Automatic Gate Repair. When the gate frame is compromised by rust, the friction increases, and the motor’s safety sensors trigger a stop to prevent damage. We verify the mechanical integrity of the gate first, as a weld repair often solves the “motor” problem by removing the source of the resistance.
Is it cheaper to replace the gate or repair the rust?
In most cases, Electric Gate Repair to fix the rust and reinforce the existing gate is significantly more cost-effective than a full replacement. Unless the steel is rusted through in multiple, non-structural locations that have compromised the entire integrity of the gate, we can typically restore it to full functionality. We will always give you an honest assessment of whether a repair is worth the investment or if the material is too far gone.
Written by Adrian Vance, Owner at Vance Gate Repair Garland, serving Garland.