Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Frisco, TX
Gate access control in Frisco means keypads, card readers, and intercoms on HOA-governed entries that were mostly installed between 2005 and 2015, are now ten to twenty years old, and are failing in clusters. The expansive clay soil under Phillips Creek Ranch and Starwood shifts posts and pulls buried conduit, while summer heat cycles bake circuit boards inside the control boxes. If your keypad stopped talking to your opener, we can usually diagnose it the same day. Call (469) 273-6254.
Why Frisco Homes Are Different
Frisco’s housing stock is almost all post-1995 construction: large brick-and-stone homes inside master-planned communities, the great majority under HOAs with strict rules about gate style, color, and picket spacing. That means most gate work here happens in subdivisions like the Villages of Stonelake and Starwood, where ornamental iron gates carry automation from LiftMaster, Elite, or Linear. Frisco sits on the North Texas Blackland Prairie, and the heavy clay soil, what locals call black gumbo, swells after wet springs and shrinks in dry summers. Swing gate posts that were perfectly plumb in April can be rotated several degrees by August, enough to make the gate drag, bind, or throw the limit switch. Technicians here learn to check the post before the board, because after a wet spring followed by a dry summer, the footing is usually the root cause. Add HOA architectural review for visible hardware changes, and a Frisco gate job often starts with paperwork before it starts with tools.
Our Main Frisco Services
Frisco homeowners call us most about these three jobs. Each one gets a written price before work starts and a photo record when our technician leaves.
Gate Repair in Frisco
Most repair calls in Frisco are swing gates dragging on clay-shifted posts, failed circuit boards from heat exposure, or misaligned photo-eyes. We diagnose first, then hand you a written price for the fix. See the full scope at Gate Repair in Frisco.
Gate Installation in Frisco
New gates in Frisco mean HOA dimensions, approved finishes like flat black or bronze powder coat, and footings poured deep enough to ride out black gumbo soil movement. We measure free and quote in writing. See Gate Installation in Frisco.
Gate Motor & Opener in Frisco
Frisco’s summer heat is hard on control boards and limit switches. We service and replace motors across nine brands, so you aren’t pushed into a whole new system because we only sell one. Details at Gate Motor & Opener in Frisco.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Frisco
Gate access control is what decides who gets in: keypads, phone entry, card readers, and video intercoms mounted on or near the driveway gate. In Frisco, most of this equipment was installed during the 2005 to 2015 building wave and is now entering its first full replacement cycle, with boards failing from heat and keypads losing digits from sun exposure. Our Gate Access Control service covers the wiring, the programming, and the hardware on any brand already on the property.
Keypad Entry
Signs you need it
Keys don’t work, or the keypad accepts some codes but not others, or the display has gone blank in direct afternoon sun.
What it costs in Frisco
Keypad replacement in Frisco typically runs $185 to $340 including the new keypad mounted and programmed to your existing opener.
How we do it
We test voltage at the keypad, pull the old unit, install the new one in the same footprint, program all entry codes, and photograph the wiring before the cover goes back on.
Phone Entry
Signs you need it
The call rings but the gate won’t open, or the system doesn’t recognize a renter’s new phone number.
What it costs in Frisco
Phone entry repair in Frisco runs $260 to $520 depending on whether the dialer or the receiver board is at fault.
How we do it
We trace the phone line or cellular signal to the relay, swap the failed component, update the tenant directory, and test call-in-to-open twice with the homeowner watching.
Video Intercom
Signs you need it
The screen stays black, audio is one-way, or the camera fogs inside the housing after rain.
What it costs in Frisco
Video intercom work in Frisco typically runs $400 to $950 for component replacement plus wiring repair at the post.
How we do it
We bench-test the monitor and camera separately, replace the failed unit, re-seal the exterior housing, and leave you with a photo log of every connection we touched.
What Gate Access Control Costs in Frisco
| Item | Typical range in Frisco |
|---|---|
| Keypad replacement | $185 - $340 |
| Phone entry module repair | $260 - $520 |
| Video intercom component replacement | $400 - $950 |
Can you program my existing keypad or do I have to buy a new one?
We reprogram the existing keypad whenever the unit itself is still sound. If the board is dead or the keypad face is delaminated from thirteen Frisco summers, replacement makes more sense than repeated repairs.
Do you handle HOA community entry systems or just single-family gates?
We handle both. For HOA entries, we coordinate with the property manager and follow the governing documents for hardware appearance. A written price still comes first. Call (469) 273-6254 to schedule a diagnostic.
Gate Parts & Welding in Frisco
Gate parts and welding in Frisco means hinge replacement, post repair, and custom welding on ornamental iron that HOAs insist stays black or bronze. Frisco’s clay soil rotates posts and cracks welds at the hinge, and our Gate Parts & Welding service re-plumbs, re-welds, and reinforces so the gate hangs straight again.
Hinge Replacement
Signs you need it
The gate sags toward the latch, scrapes the driveway, or the top hinge has visible play when you push on the gate.
What it costs in Frisco
Hinge replacement in Frisco typically runs $250 to $780 depending on gate weight and whether we grind off the old weld or bolt through.
How we do it
We support the gate on jack stands, cut or unbolt the failed hinge, weld or bolt the replacement, and align the gate to clear the latch by the same margin on both sides.
Safety note: A sagging gate under spring tension can shift suddenly. We support the gate before touching any hinge or bracket.
Post Replacement
Signs you need it
The post leans visibly, the gate gap widens at the bottom, or concrete around the base has cracked and separated.
What it costs in Frisco
Post replacement in Frisco runs $600 to $1,400 depending on depth, concrete volume, and whether the post carries automation wiring.
How we do it
We saw-cut the footing, extract the old post, set the new one plumb in fresh concrete, and re-run any low-voltage wiring through the post before the pour cures.
Safety note: A leaning post can drop a gate without warning. Don’t lean on or under a gate that’s out of plumb; call us to shore it up.
What Gate Parts & Welding Costs in Frisco
| Item | Typical range in Frisco |
|---|---|
| Hinge replacement | $250 - $780 |
| Post replacement | $600 - $1,400 |
| Custom welding repair | $175 - $600 |
Can you match an existing HOA-approved finish after welding?
Yes. We grind the weld, prime, and powder coat or paint to match the existing flat black or bronze finish. HOA reps in Frisco usually want a photo record of the completed work, which we provide.
Do you do small welding jobs or only full gate repairs?
Small jobs are a big part of our welding work. A broken picket, a cracked top rail, or a loose scroll can often be repaired in one visit with a written price first. Call (469) 273-6254 for a quote.
Brands We Service in Frisco
We service Linear, Viking, Ghost Controls, and DoorKing among nine automation brands, and we keep common control boards and photo-eyes on the truck for same-day swaps. Our technicians arrive knowing the brand already on your property, not selling a replacement. See our brands for the full list.
Pricing for Gate Repair in Frisco, TX
| Service | Typical range in Frisco |
|---|---|
| Keypad replacement | $185 - $340 |
| Phone entry module repair | $260 - $520 |
| Video intercom component replacement | $400 - $950 |
| Hinge replacement | $250 - $780 |
| Post replacement | $600 - $1,400 |
| Custom welding repair | $175 - $600 |
| Gate roller replacement | $120 - $310 |
| Rail repair and true-up | $200 - $550 |
Frisco prices run higher when a job involves clay-heaved posts, HOA-specified finishes, or automation wiring that has to be re-pulled. Every price is written and handed to you before we start, so the number on the quote is the number on the invoice.
Neighborhoods We Serve in Frisco
We run service calls across all of Frisco, from the gated entries in Starwood to the newer builds near Phillips Creek Ranch and the Villages of Stonelake. Typical response within the city is same day or next morning, with emergency calls dispatched as they come in.
- Phillips Creek Ranch
- Starwood
- Villages of Stonelake
- Panther Creek Estates
- Griffin Parc
Service Area - Cities Near Frisco
We also cover the cities around Frisco: McKinney, TX to the northeast, Plano, TX to the south, Allen, TX to the east, and Carrollton, TX to the southwest. Scheduling and dispatch run through our Dallas-Fort Worth office.
Serving Frisco, TX - Our Local Coverage Area
We’re based in the Frisco area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Frisco
Most Frisco calls get a same-day or next-morning visit. A live person answers the phone 24 hours a day, so you will never hit a voicemail loop when your gate is stuck open at night. Call (469) 273-6254 and a technician is dispatched with a name and photo before arrival.
Most Frisco HOAs require architectural review for visible hardware changes like new gate panels or changed finishes. We provide the photo records and written scope your committee will want, and we handle the work after approval is in hand.
Every visit includes a written price first and a documented photo record when we leave: what we found, what we adjusted, what we replaced. The same record goes into your job file, so any future technician can see exactly what happened.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Frisco Customers Say
"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N.