Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Irving, TX
Gate access control in Irving means working on two very different systems within the same square mile: the HOA subdivision entry gates across Valley Ranch and the commercial-grade operators guarding corporate campus entrances in Las Colinas. The clay soil here heaves and shrinks seasonally, pulling gate posts out of alignment and straining operators, while triple-digit summer heat cooks circuit boards in west-facing units. If your gate won’t open, won’t close, or won’t respond to a code, call (469) 273-6254 and we’ll put a written price in your hand before any work starts.
Why Irving Homes Are Different
Most of Las Colinas and Valley Ranch was built between the mid-1980s and late 1990s, which means hundreds of subdivision entry gates and community gates are now 25 to 40 years old, running original operators that are increasingly parts-scarce or flat-out obsolete. Central and south Irving tells a different story: 1960s and 1970s ranch-style tracts where homeowners adding a new gate have to work around existing masonry walls and narrow driveways that were never designed for automated access.
Then there’s the soil. Irving sits on Blackland Prairie expansive clay. It swells hard after spring rains and cracks during summer droughts, so gate posts heave, tilt, and shift seasonally. A gate that slides fine in May can bind in August. Add triple-digit heat degrading capacitors and circuit boards inside operators that face west or south with no shade cover, and you get a repair pattern we see every summer without fail. These aren’t generic gate problems; they’re Irving gate problems.
Our Main Irving Services
Most Irving callers reach out about one of three things: a gate that stopped working, a gate they want installed, or a motor that quit. Here’s what each looks like in Irving.
Gate Repair in Irving
A 30-year-old subdivision entry gate in Valley Ranch usually fails differently than a 10-year-old driveway gate in Las Colinas. We diagnose the actual fault, write down the price, and fix what’s broken rather than selling a replacement you don’t need. Gate Repair in Irving
Gate Installation in Irving
Older south Irving driveways are narrow and flanked by masonry that was poured before automated gates existed. Installation here means working around what’s already there: concrete cuts, custom post placement, operator selection matched to the gate’s weight. Gate Installation in Irving
Gate Motor & Opener in Irving
Many Valley Ranch HOA gates run Linear operators from the 1988 to 1998 buildout, and a lot of them are hitting end-of-life at the same time. We service what’s on the property, including Linear, Viking, Ghost Controls, and DoorKing. Gate Motor & Opener in Irving
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Irving
Gate access control in Irving spans two extremes: aging residential keypads and phone-entry systems in Valley Ranch and Las Colinas communities, and commercial-grade card readers on Fortune 500 campus entrances. The common thread is that Irving’s clay soil and summer heat stress every component, from keypad housings to underground loop wiring, and a system that works in March can fail in August. We work on all of it under Gate Access Control, with a written price before any tool comes off the truck.
Keypad Entry
Signs you need it
The keypad accepts some codes but not others, the buttons stick, or the keypad goes dead after rain.
What it costs in Irving
Keypad entry repairs and replacements typically run $150 to $850 in Irving, depending on whether we’re replacing the keypad, the controller board, or both.
How we do it
We test each code pathway, check the controller board for moisture damage, install the new keypad, and reprogram all codes, then photograph the finished work.
Phone Entry
Signs you need it
Guests call the listed number but the gate won’t open, or the line buzzes with no dial tone at the pedestal.
What it costs in Irving
Phone entry repairs in Irving typically fall between $200 and $1,200, with full replacement units running $600 to $2,500 when the board is fried.
How we do it
We check the phone line at the pedestal, test the relay, confirm the dial-out path, and replace the board or the antenna as needed, then leave a written record of every setting.
What Gate Access Control Costs in Irving
| Item | Typical range in Irving |
|---|---|
| Keypad entry repair or replacement | $150 - $850 |
| Phone entry repair | $200 - $1,200 |
| Full phone entry replacement | $600 - $2,500 |
Can you program a new code the same day in Irving?
Yes. We reprogram keypads and phone entry codes on the first visit, while the technician is on site. The written price for the visit is quoted and agreed before any work begins, and the new codes are tested before we leave.
Do you handle gate access for HOA communities in Valley Ranch?
We do. Valley Ranch HOA gates from the late 1980s and 1990s are a big part of our Irving work. We service the existing operator and access hardware rather than pushing a full replacement, and we document every setting change. Call (469) 273-6254 for a written estimate.
Gate Parts & Welding in Irving
Irving’s aging gates fail at the mechanical level as often as the electrical one: hinges rust through on 25-year-old community gates, posts heave out of plumb in the clay soil, and rails warp under summer heat. We stock and source the parts to fix what’s there, and we weld on site when the repair calls for it. Our Gate Parts & Welding work carries the same written price and photo record as every other job.
Hinge Replacement
Signs you need it
The gate sags, scrapes the ground on one side, or the hinge pin has visible rust and wear.
What it costs in Irving
Hinge replacement for a typical Irving driveway gate runs $120 to $400 per hinge, including the new hinge, hardware, and labor.
How we do it
We take the gate’s weight off the hinge, cut or unbolt the old one, weld or bolt the new hinge in place, and re-level the gate.
Post Replacement
Signs you need it
The post leans visibly, the gate binds at the latch, or the post has cracked at the base from clay-soil movement.
What it costs in Irving
Gate post replacement in Irving typically runs $400 to $1,500 per post, depending on depth, concrete work, and whether we’re also resetting the operator bracket.
How we do it
We excavate the old footing, set a new post in concrete at the correct depth for Irving’s soil movement, and remount the gate and hinges the same day where possible.
What Gate Parts & Welding Costs in Irving
| Item | Typical range in Irving |
|---|---|
| Hinge replacement (per hinge) | $120 - $400 |
| Post replacement (per post) | $400 - $1,500 |
| Rail repair or straightening | $150 - $600 |
Can you weld a gate on site in Irving?
Yes. Our technicians carry mobile welding equipment and can complete most weld repairs at the property, including hinge plates, rail cracks, and frame reinforcement. The price is written and agreed before we strike an arc. Call (469) 273-6254 for an exact quote.
Do you stock parts for older Irving gates?
We stock common hinge sizes, rollers, brackets, and hardware for the gate models most common in Irving’s 1980s and 1990s neighborhoods, and we source harder-to-find parts through our supplier network. If a part is obsolete, we’ll tell you and quote a workable substitute.
Brands We Service in Irving
We service Linear, Viking, Ghost Controls, and DoorKing operators in Irving, along with five other major automation brands. Our trucks carry common boards, remotes, and safety components for the models most common in Valley Ranch and Las Colinas, which shortens turnaround on repairs. See our brands for the full list.
Pricing for Gate Repair in Irving, TX
| Service | Typical range in Irving |
|---|---|
| Gate repair (general diagnosis and fix) | $95 - $850 |
| Keypad entry repair or replacement | $150 - $850 |
| Phone entry repair | $200 - $1,200 |
| Full phone entry replacement | $600 - $2,500 |
| Hinge replacement (per hinge) | $120 - $400 |
| Post replacement (per post) | $400 - $1,500 |
| Rail repair or straightening | $150 - $600 |
| Gate roller replacement (per roller) | $50 - $150 |
| Custom welding | $100 - $800 |
| Gate opener motor replacement | $450 - $1,500 |
| Gate installation (full, new gate) | $1,800 - $8,000 |
| Gate opener installation (new operator) | $800 - $2,500 |
What pushes price up in Irving is usually soil movement: a post that heaved out of plumb means concrete work on top of the part replacement, and a gate that’s binding from post shift strains the operator and wears parts faster than a level gate. The price we quote is the price you pay, written down and agreed before any work begins.
Neighborhoods We Serve in Irving
We work across Irving, from the gated communities of Valley Ranch and Las Colinas to the older ranch-style tracts in central and south Irving. Response time is typically same-day or next-day for most calls, and emergency gate failures get priority routing.
- Valley Ranch
- Las Colinas
- University Hills
- Heritage District
- MacArthur Corridor
Service Area - Cities Near Irving
From our Dallas-Fort Worth dispatch office, we also serve homeowners in Dallas, TX, Mesquite, TX, Sunnyvale, TX, and Richardson, TX. Call (469) 273-6254 and a live person answers, any hour, any day.
Serving Irving, TX - Our Local Coverage Area
We’re based in the Irving area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Irving
For a gate stuck open or a safety hazard, we prioritize Irving calls and typically arrive same-day. A gate that won’t close is a security issue, not just an inconvenience. Call (469) 273-6254 and describe what the gate is doing; we’ll tell you what to check and get a technician dispatched.
In most Irving HOAs, repairing an existing gate and operator doesn’t require approval, but changing the gate’s appearance, size, or operator type might. We can provide a written scope and photo record of any repair, which most HOA boards accept as documentation. Check your HOA’s architectural guidelines before major changes.
Yes. Las Colinas corporate campus gates are a significant part of our Irving work, and our commercial access-control background means we handle card readers, phone entry, and high-traffic operators daily. The same written-price and photo-record standard applies to every commercial job. Call (469) 273-6254 with the gate’s brand and symptom for a same-day assessment.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Irving Customers Say
"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N.